Garmin Nuvi 1350 Battery Installation Instructions

The following instructions are the Garmin Nuvi 1350 battery installation instructions.

1. To begin use the pry tool to remove the Nuvi's primary faceplate. Slide the prytool in the groove around the outside edges of the faceplate (this is the black cover that goes around the face of the nuvi to protect the screen if you lay the nuvi face down). When done you will see 4 screws (1 on each the 4 corners).
 
2. Remove the four screws using the torx provided in your Kit from BatteryShip.com.
 
3. Once the screw are removed, remove the Garmin's secondary faceplate by running the pry tool around the edge of the Garmin. This will separate the 2 halves.
 
4. Next slowly and carefully pull your Garmin screen up and forward. Do not completely separate the 2 halves as a ribbon cable is attached on and connects both sides (this is what powers and controls you screen).
 
4. Next you will need to lift up the circuit board. To do this you have to remove the 2 screws that hold the circuit board in place. Use the tools that came in your kit to remove the 2 screws securing the circuit board.
 
5. Once the circuit board screws are removed carefully lift the circuit board so that you can access the battery connector. Hint: as you remove the screws of the circuit board you will see the battery. Garmin designed the circuit board so that the battery connector would have to be connected on the bottom of the board. So once you lift the board up a little you will be able to grab the battery cable and disconnect the battery from the circuit board.
 
6. Next pry the original battery up.
 
7. Replace the original Garmin Nuvi 1350 Battery with one from BatteryShip.com and connect the new battery back to the circuit board.
 
8. Replace the circuit board to its original position and screw the circuit board back in place.
 
9. Return the screen back to its original position and attach the secondary faceplate to the screen.
 
10. Replace the 4 screws around the 4 corners of the Garmin.
 
11. Replace the primary faceplate by securely snapping in the plate all the way around the Nuvi.
 
12. Charge your new Garmin Nuvi 1350 Battery for 4 hours and then turn on.
 
PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

Garmin Nuvi 1300 Battery Installation Instructions

The following instructions are the Garmin Nuvi 1300 battery installation instructions.

1. To begin use the pry tool to remove the Nuvi's primary faceplate. Slide the prytool in the groove around the outside edges of the faceplate (this is the black cover that goes around the face of the nuvi to protect the screen if you lay the nuvi face down). When done you will see 4 screws (1 on each the 4 corners).
 
2. Remove the four screws using the torx provided in your Kit from BatteryShip.com.
 
3. Once the screw are removed, remove the Garmin's secondary faceplate by running the pry tool around the edge of the Garmin. This will separate the 2 halves.
 
4. Next slowly and carefully pull your Garmin screen up and forward. Do not completely separate the 2 halves as a ribbon cable is attached on and connects both sides (this is what powers and controls you screen).
 
4. Next you will need to lift up the circuit board. To do this you have to remove the 2 screws that hold the circuit board in place. Use the tools that came in your kit to remove the 2 screws securing the circuit board.
 
5. Once the circuit board screws are removed carefully lift the circuit board so that you can access the battery connector. Hint: as you remove the screws of the circuit board you will see the battery. Garmin designed the circuit board so that the battery connector would have to be connected on the bottom of the board. So once you lift the board up a little you will be able to grab the battery cable and disconnect the battery from the circuit board.
 
6. Next pry the original battery up.
 
7. Replace the original Garmin Nuvi 1300 Battery with one from BatteryShip.com and connect the new battery back to the circuit board.
 
8. Replace the circuit board to its original position and screw the circuit board back in place.
 
9. Return the screen back to its original position and attach the secondary faceplate to the screen.
 
10. Replace the 4 screws around the 4 corners of the Garmin.
 
11. Replace the primary faceplate by securely snapping in the plate all the way around the Nuvi.
 
12. Charge your new Garmin Nuvi 1300 Battery for 4 hours and then turn on.
 
PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

Sony PRS-300BC Battery Installation Instructions

The following are the Sony PRS-300BC Battery Replacement Instruction guide.

1. Begin by removing all the screws at the top and base and back of your Sony.
 
2. Next using the pry tool remove the plastic frame/seal from the outside frame of the device.

3. Next detach the clips holding the back cover. Use your pry tool to help detach the clips. The clips hold the back cover in place.
 
4. Now remove the back cover.

5. Disconnect and remove the battery by using the pry tool to lift the battery up and out.

6. Replace the old battery with a brand new Sony PRS-300BC Battery Replacement from BatteryShip.com.
 
Now let's reverse our steps.

7. Replace the back cover and snap into clips.

8. Carefully snap on the plastic frame/seal to the outside frame of the device.
 
9. Replace all the screws froma around the device.

10. Charge your Sony PRS-300BC Battery for four hours. Then turn on your Sony.
 
PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

Sony PRS-300RC Battery Installation Instructions

The following are the Sony PRS-300RC Battery Replacement Instruction guide.

1. Begin by removing all the screws at the top and base and back of your Sony.
 
2. Next using the pry tool remove the plastic frame/seal from the outside frame of the device.

3. Next detach the clips holding the back cover. Use your pry tool to help detach the clips. The clips hold the back cover in place.
 
4. Now remove the back cover.

5. Disconnect and remove the battery by using the pry tool to lift the battery up and out.

6. Replace the old battery with a brand new Sony PRS-300RC Battery Replacement from BatteryShip.com.
 
Now let's reverse our steps.

7. Replace the back cover and snap into clips.

8. Carefully snap on the plastic frame/seal to the outside frame of the device.
 
9. Replace all the screws froma around the device.

10. Charge your Sony PRS-300RC Battery for four hours. Then turn on your Sony.
 
PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

Sony PRS-300SC Battery Installation Instructions

The following are the Sony PRS-300SC Battery Replacement Instruction guide.

1. Begin by removing all the screws at the top and base and back of your Sony.
 
2. Next using the pry tool remove the plastic frame/seal from the outside frame of the device.

3. Next detach the clips holding the back cover. Use your pry tool to help detach the clips. The clips hold the back cover in place.
 
4. Now remove the back cover.

5. Disconnect and remove the battery by using the pry tool to lift the battery up and out.

6. Replace the old battery with a brand new Sony PRS-300SC Battery Replacement from BatteryShip.com.
 
Now let's reverse our steps.

7. Replace the back cover and snap into clips.

8. Carefully snap on the plastic frame/seal to the outside frame of the device.
 
9. Replace all the screws froma around the device.

10. Charge your Sony PRS-300SC Battery for four hours. Then turn on your Sony.
 
PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

Sony PRS-300 Battery Installation Instructions

The following are the Sony PRS-300 Battery Replacement Instruction guide.

1. Begin by removing all the screws at the top and base and back of your Sony.
 
2. Next using the pry tool remove the plastic frame/seal from the outside frame of the device.

3. Next detach the clips holding the back cover. Use your pry tool to help detach the clips. The clips hold the back cover in place.
 
4. Now remove the back cover.

5. Disconnect and remove the battery by using the pry tool to lift the battery up and out.

6. Replace the old battery with a brand new Sony PRS-300 Battery Replacement from BatteryShip.com.
 
Now let's reverse our steps.

7. Replace the back cover and snap into clips.

8. Carefully snap on the plastic frame/seal to the outside frame of the device.
 
9. Replace all the screws froma around the device.

10. Charge your Sony PRS-300 Battery for four hours. Then turn on your Sony.
 
PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

Garmin Nuvi 1690T Battery Installation Instructions

The following instructions may can be used to install a Garmin Nuvi 1690T Battery.

1. Begin by turning your Nuvi face down. On the bottom of the Nuvi there will be 2 screws hidden under the label. Peel back the label to reveal these two screws.
 
2. Remove the two screws.
 
3. Next using the pry tool provided in your tool kit gently open the GPS by carefully separating the 2 halves (slide the pry tool all around the edge until the halves come apart). CAUTION as you open the the 2 sides (on the inside) they will be connected by cables. So please be careful not to rip apart the 2 halves.

4. After opening the two halves you will see 4 screws that hold the circuit board in place. Remove these four screws to access the battery. A small plastic piece may come out during the replacement. This piece is the power switch. Do not worry it is normal. We will put it back in during step 9.
 
5. Carefully lift up the circuit board to access the original battery.
 
6. Disconnect the original battery and pry it up. Garmin uses an adhesive to hold the Nuvi battery in place. Use the pry bar provided to help pry up the battery.
 
7. Place a brand new Garmin Nuvi 1690T Battery from BatteryShip into the device and connect the new battery to the circuit board. The battery should be oriented the same as the original.
 
Now let's reverse our steps.
 
8. Return the circuit board to its original position and replace the four screws to secure the circuit board.
 
9. A small plastic piece may have come out during the replacement. This piece is the power switch. Place the switch back into place. Now put the 2 halves of the GPS together and gently snap in place.
 
10. Carefully lift the label at the base of your Nuvi and replace the two screws removed in step 2.
 
11. Charge your Garmin Nuvi 1690T Battery for four hours. Then turn on your Garmin.
 
PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

Garmin Nuvi 1690 Battery Installation Instructions

The following instructions may can be used to install a Garmin Nuvi 1690 Battery.

1. Begin by turning your Nuvi face down. On the bottom of the Nuvi there will be 2 screws hidden under the label. Peel back the label to reveal these two screws.
 
2. Remove the two screws.
 
3. Next using the pry tool provided in your tool kit gently open the GPS by carefully separating the 2 halves (slide the pry tool all around the edge until the halves come apart). CAUTION as you open the the 2 sides (on the inside) they will be connected by cables. So please be careful not to rip apart the 2 halves.

4. After opening the two halves you will see 4 screws that hold the circuit board in place. Remove these four screws to access the battery. A small plastic piece may come out during the replacement. This piece is the power switch. Do not worry it is normal. We will put it back in during step 9.
 
5. Carefully lift up the circuit board to access the original battery.
 
6. Disconnect the original battery and pry it up. Garmin uses an adhesive to hold the Nuvi battery in place. Use the pry bar provided to help pry up the battery.
 
7. Place a brand new Garmin Nuvi 1690 Battery from BatteryShip into the device and connect the  new battery to the circuit board. The battery should be oriented the same as the original.
 
Now let's reverse our steps.

8. Return the circuit board to its original position and replace the four screws to secure the circuit board.
 
9. A small plastic piece may have come out during the replacement. This piece is the power switch. Place the switch back into place. Now put the 2 halves of the GPS together and gently snap in place.
 
10. Carefully lift the label at the base of your Nuvi and replace the two screws removed in step 2.
 
11. Charge your Garmin Nuvi 1690 Battery for four hours. Then turn on your Garmin.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions,  you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

Magellan Maestro Elite 5340 Battery Installation Instructions

The following instruction guide may be used to replace the Magellan Maestro Elite 5340 Battery.

1.  Begin by removing the four screws on the back of your Magellan. The four screws are hidden under 4 rubber caps. To remove the caps use the pry tool to carefully lift them (or a sharp metal object). After the rubber caps are removed then remove the screws.
 
2. Next using the pry tool carefully slide the pry tool around the plastic cover that holds the screen and circuit board in place. This will open the device.

3. With the pry tool carefully lift up the screen and circuit board. Go slowly here. You do not want to cause any damage to the charging port.
 
4. Next disconnect the original battery to open the two sides.

5. Next pry up the original battery. Replace the battery with a new Magellan Maestro Elite 5340 Battery Replacement from www.BatteryShip.com. Be sure to orient your new battery just like the old. You may want add a small piece of double sided tape to help hold the new battery in place. Connect the new battery.
 
Now we need to reverse our steps…
 
6. Reseat the screen and circuit board to their original position.

7. Carefully seat the GPS receiver.

8. Carefully snap the cover shut (this was removed in step 2).

9. Replace the 4 screws removed in step 1 and then replace the rubber caps over each screw.

10. Charge your new Magellan Maestro Elite 5340 Battery for 4 hours and then turn on.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

Magellan Maestro 5310 Battery Installation Instructions

The following instruction guide may be used to replace the Magellan Maestro 5310 Battery.

1.  Begin by removing the four screws on the back of your Magellan. The four screws are hidden under 4 rubber caps. To remove the caps use the pry tool to carefully lift them (or a sharp metal object). After the rubber caps are removed then remove the screws.
 
2. Next using the pry tool carefully slide the pry tool around the plastic cover that holds the screen and circuit board in place. This will open the device.

3. With the pry tool carefully lift up the screen and circuit board. Go slowly here. You do not want to cause any damage to the charging port.
 
4. Next disconnect the original battery to open the two sides.

5. Next pry up the original battery. Replace the battery with a new Magellan Maestro 5310 Battery Replacement from www.BatteryShip.com. Be sure to orient your new battery just like the old. You may want add a small piece of double sided tape to help hold the new battery in place. Connect the new battery.
 
Now we need to reverse our steps…
 
6. Reseat the screen and circuit board to their original position.

7. Carefully seat the GPS receiver.

8. Carefully snap the cover shut (this was removed in step 2).

9. Replace the 4 screws removed in step 1 and then replace the rubber caps over each screw.

10. Charge your new Magellan Maestro 5310 Battery for 4 hours and then turn on.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.