Category: Battery Replacement Instructions – GPS Devices

Magellan RoadMate 2036-MU Battery Installation Instructions

The following instruction guide may be used to replace the Magellan RoadMate 2036-MU Battery.

1. Begin by turning your Roadmate face down. On the back there will be 6 screws. Remove the six screws.

2. Next using the pry tool provided in your tool kit gently open the GPS by carefully separating the 2 halves (slide the pry tool all around the edge until the halves come apart). CAUTION as you open the the 2 sides (on the inside) they will be connected by cables. So please be careful not to rip apart the 2 halves. Also please be aware a small plast piece may fall out of place. This piece is your power switch. If it falls out do not worry we will put it back in step 6.

3. Next remove the piece of tape covering the battery connector from the circuit board. And disconnect the original battery (once done you will be able to open both halves but still be careful as there is a cable that remain connected to both halves).

4. Pry out the original battery.

5. Replace the old battery with a new Magellan Roadmate 2036-MU Battery from Batteryship.com and connect the battery to the circuit board (reapply the tape). Be sure orient the new battery just as the original. It may be helpful to add a strip of double-sided tape in the battery compartment to help secure the battery in place so that it does not move around.

Now let's reverse our steps.

6. If your power switch came off put it back into place.

7. Now put the 2 halves of the GPS together and gently snap in place.

8. Screw in all 6 screws removed in step 1.

9. Charge your Magellan Roadmate 2036-MU Battery for four hours. Then turn on your Magellan.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

Magellan RoadMate 2036 Battery Installation Instructions

The following instruction guide may be used to replace the Magellan RoadMate 2036 Battery.

1. Begin by turning your Roadmate face down. On the back there will be 6 screws. Remove the six screws.

2. Next using the pry tool provided in your tool kit gently open the GPS by carefully separating the 2 halves (slide the pry tool all around the edge until the halves come apart). CAUTION as you open the the 2 sides (on the inside) they will be connected by cables. So please be careful not to rip apart the 2 halves. Also please be aware a small plast piece may fall out of place. This piece is your power switch. If it falls out do not worry we will put it back in step 6.

3. Next remove the piece of tape covering the battery connector from the circuit board. And disconnect the original battery (once done you will be able to open both halves but still be careful as there is a cable that remain connected to both halves).

4. Pry out the original battery.

5. Replace the old battery with a new Magellan Roadmate 2036 Battery from Batteryship.com and connect the battery to the circuit board (reapply the tape). Be sure orient the new battery just as the original. It may be helpful to add a strip of double-sided tape in the battery compartment to help secure the battery in place so that it does not move around.

Now let's reverse our steps.

6. If your power switch came off put it back into place.

7. Now put the 2 halves of the GPS together and gently snap in place.

8. Screw in all 6 screws removed in step 1.

9. Charge your Magellan Roadmate 2036 Battery for four hours. Then turn on your Magellan.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

Magellan RoadMate 2035 Battery Installation Instructions

The following instruction guide may be used to replace the Magellan RoadMate 2035 Battery.

1. Begin by turning your Roadmate face down. On the back there will be 6 screws. Remove the six screws.

2. Next using the pry tool provided in your tool kit gently open the GPS by carefully separating the 2 halves (slide the pry tool all around the edge until the halves come apart). CAUTION as you open the the 2 sides (on the inside) they will be connected by cables. So please be careful not to rip apart the 2 halves. Also please be aware a small plast piece may fall out of place. This piece is your power switch. If it falls out do not worry we will put it back in step 6.

3. Next remove the piece of tape covering the battery connector from the circuit board. And disconnect the original battery (once done you will be able to open both halves but still be careful as there is a cable that remain connected to both halves).

4. Pry out the original battery.

5. Replace the old battery with a new Magellan Roadmate 2035 Battery from Batteryship.com and connect the battery to the circuit board (reapply the tape). Be sure orient the new battery just as the original. It may be helpful to add a strip of double-sided tape in the battery compartment to help secure the battery in place so that it does not move around.

Now let's reverse our steps.

6. If your power switch came off put it back into place.

7. Now put the 2 halves of the GPS together and gently snap in place.

8. Screw in all 6 screws removed in step 1.

9. Charge your Magellan Roadmate 2035 Battery for four hours. Then turn on your Magellan.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

Garmin Nuvi 1490LMT Battery Installation Instructions

The following instruction guide may be used to replace the Garmin Nuvi 1490LMT Battery

1. To begin use the pry tool to remove the Nuvi's primary faceplate. Slide the prytool in the groove around the outside edges of the faceplate (this is the black cover that goes around the face of the nuvi to protect the screen if you lay the nuvi face down). When done you will see 4 screws (1 on each the 4 corners).

2. Remove the four screws using the torx provided in your Kit from BatteryShip.com.

3. Once the screw are removed, remove the Garmin's secondary faceplate by running the pry tool around the edge of the Garmin. This will separate the 2 halves.

4. Next slowly and carefully pull your Garmin screen up and forward. Do not completely separate the 2 halves as a ribbon cable is attached on and connects both sides (this is what powers and controls you screen).

4. Next you will need to lift up the circuit board. To do this you have to remove the 2 screws that hold the circuit board in place. Use the tools that came in your kit to remove the 2 screws securing the circuit board.

5. Once the circuit board screws are removed carefully lift the circuit board so that you can access the battery connector. Hint: as you remove the screws of the circuit board you will see the batter. Garmin designed the circuit board so that the battery connector would have to be connected on the bottom of the board. So once you lift the board up a little you will be able to grab the battery cable and disconnect the battery from the circuit board.

6. Next pry the original battery up.

7. Replace the original Garmin Nuvi 1490LMT Battery with one from BatteryShip.com and connect the new battery back to the circuit board.

8. Replace the circuit board to its original position and screw the circuit board back in place.

9. Return the screen back to its original position and attach the secondary faceplate to the screen.

10. Replace the 4 screws around the 4 corners of the Garmin.

11. Replace the primary faceplate by securely snapping in the plate all the way around the Nuvi.

12. Charge your new Garmin Nuvi 1490LMT Battery for 4 hours and then turn on.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty
you have on your device. Please read all instructions BEFORE replacing the battery.

Garmin Nuvi 1490TV Battery Installation Instructions

The following instruction guide may be used to replace the Garmin Nuvi 1490TV Battery :

1. To begin use the pry tool to remove the Nuvi's primary faceplate. Slide the prytool in the groove around the outside edges of the faceplate (this is the black cover that goes around the face of the nuvi to protect the screen if you lay the nuvi face down). When done you will see 4 screws (1 on each the 4 corners).

2. Remove the four screws using the torx provided in your Kit from BatteryShip.com.

3. Once the screw are removed, remove the Garmin's secondary faceplate by running the pry tool around the edge of the Garmin. This will separate the 2 halves.

4. Next slowly and carefully pull your Garmin screen up and forward. Do not completely separate the 2 halves as a ribbon cable is attached on and connects both sides (this is what powers and controls you screen).

4. Next you will need to lift up the circuit board. To do this you have to remove the 2 screws that hold the circuit board in place. Use the tools that came in your kit to remove the 2 screws securing the circuit board.

5. Once the circuit board screws are removed carefully lift the circuit board so that you can access the battery connector. Hint: as you remove the screws of the circuit board you will see the batter. Garmin designed the circuit board so that the battery connector would have to be connected on the bottom of the board. So once you lift the board up a little you will be able to grab the battery cable and disconnect the battery from the circuit board.

6. Next pry the original battery up.

7. Replace the original Garmin Nuvi 1490TV Battery with one from BatteryShip.com and connect the new battery back to the circuit board.

8. Replace the circuit board to its original position and screw the circuit board back in place.

9. Return the screen back to its original position and attach the secondary faceplate to the screen.

10. Replace the 4 screws around the 4 corners of the Garmin.

11. Replace the primary faceplate by securely snapping in the plate all the way around the Nuvi.

12. Charge your new Garmin Nuvi 1490TV Battery for 4 hours and then turn on.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

Garmin Nuvi 1490T Pro Battery Installation Instructions

The following instruction guide may be used to replace the Garmin Nuvi 1490T Pro Battery :

1. To begin use the pry tool to remove the Nuvi's primary faceplate. Slide the prytool in the groove around the outside edges of the faceplate (this is the black cover that goes around the face of the nuvi to protect the screen if you lay the nuvi face down). When done you will see 4 screws (1 on each the 4 corners).

2. Remove the four screws using the torx provided in your Kit from BatteryShip.com.

3. Once the screw are removed, remove the Garmin's secondary faceplate by running the pry tool around the edge of the Garmin. This will separate the 2 halves.

4. Next slowly and carefully pull your Garmin screen up and forward. Do not completely separate the 2 halves as a ribbon cable is attached on and connects both sides (this is what powers and controls you screen).

4. Next you will need to lift up the circuit board. To do this you have to remove the 2 screws that hold the circuit board in place. Use the tools that came in your kit to remove the 2 screws securing the circuit board.

5. Once the circuit board screws are removed carefully lift the circuit board so that you can access the battery connector. Hint: as you remove the screws of the circuit board you will see the batter. Garmin designed the circuit board so that the battery connector would have to be connected on the bottom of the board. So once you lift the board up a little you will be able to grab the battery cable and disconnect the battery from the circuit board.

6. Next pry the original battery up.

7. Replace the original Garmin Nuvi 1490T Pro Battery with one from BatteryShip.com and connect the new battery back to the circuit board.

8. Replace the circuit board to its original position and screw the circuit board back in place.

9. Return the screen back to its original position and attach the secondary faceplate to the screen.

10. Replace the 4 screws around the 4 corners of the Garmin.

11. Replace the primary faceplate by securely snapping in the plate all the way around the Nuvi.

12. Charge your new Garmin Nuvi 1490T Pro Battery for 4 hours and then turn on.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty
you have on your device. Please read all instructions BEFORE replacing the battery.

Garmin Nuvi 1450T Battery Installation Instructions

The following instruction guide may be used to replace the Garmin Nuvi 1450T Battery :

1. To begin use the pry tool to remove the Nuvi's primary faceplate. Slide the prytool in the groove around the outside edges of the faceplate (this is the black cover that goes around the face of the nuvi to protect the screen if you lay the nuvi face down). When done you will see 4 screws (1 on each the 4 corners).

2. Remove the four screws using the torx provided in your Kit from BatteryShip.com.

3. Once the screw are removed, remove the Garmin's secondary faceplate by running the pry tool around the edge of the Garmin. This will separate the 2 halves.

4. Next slowly and carefully pull your Garmin screen up and forward. Do not completely separate the 2 halves as a ribbon cable is attached on and connects both sides (this is what powers and controls you screen).

4. Next you will need to lift up the circuit board. To do this you have to remove the 2 screws that hold the circuit board in place. Use the tools that came in your kit to remove the 2 screws securing the circuit board.

5. Once the circuit board screws are removed carefully lift the circuit board so that you can access the battery connector. Hint: as you remove the screws of the circuit board you will see the batter. Garmin designed the circuit board so that the battery connector would have to be connected on the bottom of the board. So once you lift the board up a little you will be able to grab the battery cable and disconnect the battery from the circuit board.

6. Next pry the original battery up.

7. Replace the original Garmin Nuvi 1450T Battery with one from BatteryShip.com and connect
the new battery back to the circuit board.

8. Replace the circuit board to its original position and screw the circuit board back in place.

9. Return the screen back to its original position and attach the secondary faceplate to the screen.

10. Replace the 4 screws around the 4 corners of the Garmin.

11. Replace the primary faceplate by securely snapping in the plate all the way around the Nuvi.

12. Charge your new Garmin Nuvi 1450T Battery for 4 hours and then turn on.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

SkyGolf SkyCaddie SG5 Battery Replacement Instructions

The following are the SkyGolf SkyCaddie SG5 Battery Replacement Instruction guide.

1. Begin by laying your Skycaddie SG5 face down.

2. Loosen the battery cover screw and gently pull back the rubber USB cover.

3. Remove the old battery.

4. Replace the old battery by inserting a brand new SkyGolf Skycaddie SG5 Battery from BatteryShip.com. The battery will be inserted at an angle so be sure to align the two pegs on each side of the battery with the channels on the SkyCaddie. Slide the battery down to snap it into place.

5. Replace the battery cover.

6. Charge your new battery for four hours. Then turn on your SG5.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

SkyGolf SG2 Battery Replacement Instructions

The following are the SkyGolf SG2 Battery Replacement Instruction guide.

1. Begin by laying your Skygolf SG2 face down and remove the three recessed screws on the back.

2. Next carefully open the plug on the side of the SkyCaddie.

3. Next holding the GPS unit in your hand (with the screen facing downward) gently pull down the front plate of the unit and put the bottom half of the unit on a table with the belt clip facing down.

4. Next if there is a plastic bar on the right side push that upwards and then remove the battery. If no bar is present simply disconnect the old battery.

5. Replace the old battery by inserting and plugging in a brand new SkyGolf SG2 Battery from BatteryShip.com. Be certain to orient the new battery the same way the old one was oriented (at the bottom of where the circuit board is located; be sure to place the red wire on the left and set the wires along the top of the battery).

Now let's reverse our steps.

6. Place the front half of the GPS unit onto the back half and align the sides and connect them.

7. Carefully press the two halves together and replace the screws removed in step 1.

8. Place the rubber plug back in the right hand side of the Skygolf and charge your new battery for four hours. Then turn on your SG2.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

TomTom XXL540S Battery Replacement Instructions

The following are the TomTom XXL540S Battery Replacement Instruction guide.

1. Begin by lifitng the label at the base of the TomTom to access the screws underneath.

2. Remove the 2 screws.

3. Next using the pry tool provided in your tool kit gently open the GPS by carefully separating the 2 halves (slide the pry tool all around the edge until the halves come apart). CAUTION as you open the the 2 sides (on the inside) they will be connected by cables. So please be careful not to rip apart the 2 halves.

3. Next remove the 3 screws securing the circuit board.

4. Now carefully lift the circuit board and disconnect the original battery.

5. Pry out the original battery.

6. Replace the old battery with a new TomTom XXL540S Battery from Batteryship.com and connect the battery to the circuit board. Be sure orient the new battery just as the original. It may be helpful to add a strip of double-sided tape in the battery compartment to help secure the battery in place so that it does not move around.

Now let's reverse our steps.

6. Replace and secure the circuit board with the 3 screws you removed earlier in step 3.

7. Now put the 2 halves of the GPS together and gently snap in place.

8. Screw in 2 screws removed in step 1 and 2.

9. Charge your TomTom XXL540S Battery for four hours. Then turn on.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.