Author: BatteryEducation

Garmin Nuvi 350 Battery Replacement Instructions

The following Garmin Nuvi 350 Battery Replacement Instruction guide can be used for the following models:

Garmin Nuvi 350 Battery 

1. Begin by laying your Nuvi face down and lift open your receiver.

2. Once the receiver is lifted open you will see 2 screws on the back of your receiver that will need to be removed.

3. Once the screws are removed you will be able to pry open the receiver and locate the black plastic spring cover at the base.

4. Using a sharp object press into the spring cover (inward) to release the spring that secures the receiver.

5. Gently unfasten the receiver and remove the spring to reveal the 2 screws that holds the Garmin Nuvi together (the yellow ribbon cable should remain attached).

6. Remove the 2 screws with screwdrivers provided in your battery replacement kit you received from BatteryShip.com.

7. Carefully open the Garmin using your pry tool (you will be separating the Nuvi case until it snaps open)

8.  Once seperated shift the upper portion of the Garmin to the side to reveal 2 screws.

9. Remove the screws and gently lift the circuit board with the pry tool.

10. Once the circuit board is lifted you will first see 2 white (plastic) connectors with wires leading out. Remove these connectors by pulling them out. One of the connectors is the old battery.

11. Open up (or separate the Nuvi).

12. Remove the old battery.

13. Install the new Garmin Nuvi 350 Battery from BatteryShip.com.

14. Reattach the 2 connectors.

15. Replace the circuit board and screws.

16. Gently snap the Garmin Nuvi shut.

17. Replace the 2 screws you removed in step 6.

18. Return the spring to its original position and snap the receiver in place.

19. Replace the screws on the back of the receiver.

20. Close the receiver and charge your battery for 4+ hours.

*****PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

Garmin Nuvi 310T Battery Replacement Instructions

The following Garmin Nuvi 310T Battery Replacement Instruction guide can be used for the following models:

Garmin Nuvi 310T Battery 

1. Begin by laying your Nuvi face down and lift open your receiver.

2. Once the receiver is lifted open you will see 2 screws on the back of your receiver that will need to be removed.

3. Once the screws are removed you will be able to pry open the receiver and locate the black plastic spring cover at the base.

4. Using a sharp object press into the spring cover (inward) to release the spring that secures the receiver.

5. Gently unfasten the receiver and remove the spring to reveal the 2 screws that holds the Garmin Nuvi together (the yellow ribbon cable should remain attached).

6. Remove the 2 screws with screwdrivers provided in your battery replacement kit you received from BatteryShip.com.

7. Carefully open the Garmin using your pry tool (you will be separating the Nuvi case until it snaps open)

8.  Once seperated shift the upper portion of the Garmin to the side to reveal 2 screws.

9. Remove the screws and gently lift the circuit board with the pry tool.

10. Once the circuit board is lifted you will first see 2 white (plastic) connectors with wires leading out. Remove these connectors by pulling them out. One of the connectors is the old battery.

11. Open up (or separate the Nuvi).

12. Remove the old battery.

13. Install the new Garmin Nuvi 310T Battery  from BatteryShip.com.

14. Reattach the 2 connectors.

15. Replace the circuit board and screws.

16. Gently snap the Garmin Nuvi shut.

17. Replace the 2 screws you removed in step 6.

18. Return the spring to its original position and snap the receiver in place.

19. Replace the screws on the back of the receiver.

20. Close the receiver and charge your battery for 4+ hours

*****PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

 

Garmin Nuvi 310 Battery Replacement Instructions

The following Garmin Nuvi 310 Battery Replacement Instruction guide can be used for the following models:

Garmin Nuvi 310 Battery 

1. Begin by laying your Nuvi face down and lift open your receiver.

2. Once the receiver is lifted open you will see 2 screws on the back of your receiver that will need to be removed.

3. Once the screws are removed you will be able to pry open the receiver and locate the black plastic spring cover at the base.

4. Using a sharp object press into the spring cover (inward) to release the spring that secures the receiver.

5. Gently unfasten the receiver and remove the spring to reveal the 2 screws that holds the Garmin Nuvi together (the yellow ribbon cable should remain attached).

6. Remove the 2 screws with screwdrivers provided in your battery replacement kit you received from BatteryShip.com.

7. Carefully open the Garmin using your pry tool (you will be separating the Nuvi case until it snaps open)

8.  Once seperated shift the upper portion of the Garmin to the side to reveal 2 screws.

9. Remove the screws and gently lift the circuit board with the pry tool.

10. Once the circuit board is lifted you will first see 2 white (plastic) connectors with wires leading out. Remove these connectors by pulling them out. One of the connectors is the old battery.

11. Open up (or separate the Nuvi).

12. Remove the old battery.

13. Install the new Garmin Nuvi 310 Battery from BatteryShip.com.

14. Reattach the 2 connectors.

15. Replace the circuit board and screws.

16. Gently snap the Garmin Nuvi shut.

17. Replace the 2 screws you removed in step 6.

18. Return the spring to its original position and snap the receiver in place.

19. Replace the screws on the back of the receiver.

20. Close the receiver and charge your battery for 4+ hours

*****PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

 

Garmin Nuvi 300 Battery Replacement Instructions

The following Garmin Nuvi 300 Battery Replacement Instruction guide can be used for the following models:

Garmin Nuvi 300 Battery 

1. Begin by laying your Nuvi face down and lift open your receiver.

2. Once the receiver is lifted open you will see 2 screws on the back of your receiver that will need to be removed.

3. Once the screws are removed you will be able to pry open the receiver and locate the black plastic spring cover at the base.

4. Using a sharp object press into the spring cover (inward) to release the spring that secures the receiver.

5. Gently unfasten the receiver and remove the spring to reveal the 2 screws that holds the Garmin Nuvi together (the yellow ribbon cable should remain attached).

6. Remove the 2 screws with screwdrivers provided in your battery replacement kit you received from BatteryShip.com.

7. Carefully open the Garmin using your pry tool (you will be separating the Nuvi case until it snaps open)

8.  Once seperated shift the upper portion of the Garmin to the side to reveal 2 screws.

9. Remove the screws and gently lift the circuit board with the pry tool.

10. Once the circuit board is lifted you will first see 2 white (plastic) connectors with wires leading out. Remove these connectors by pulling them out. One of the connectors is the old battery.

11. Open up (or separate the Nuvi).

12. Remove the old battery.

13. Install the new Garmin Nuvi 300 Battery from BatteryShip.com.

14. Reattach the 2 connectors.

15. Replace the circuit board and screws.

16. Gently snap the Garmin Nuvi shut.

17. Replace the 2 screws you removed in step 6.

18. Return the spring to its original position and snap the receiver in place.

19. Replace the screws on the back of the receiver.

20. Close the receiver and charge your battery for 4+ hours.

*****PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

 

Garmin Nuvi 765T Battery Installation Instructions

The following Garmin Nuvi 765T Battery Replacement Instruction guide can be used for the following models: 

Garmin Nuvi 765T Battery

1. Begin by turning your nuvi 765T face down.

2. On the back near the bottom there will be 2 small screws. Remove those screws with the T4 screw driver provided.

3. Next using the pry tool provided separate the housing case being sure to separate all around the Garmin.

4. Lift up the front portion of the nuvi being careful not to fully separate the two parts as the battery connector and the speaker connector will be attached and connected. Lift just enough to see the battery and the connectors.

(At this point you have 2 options at this point – either disconnect both the speaker wire connector and the battery connector to full separate both halves or simply disconnect the battery cable. You can do whatever is easier for you.)

5. Now disconnect the old battery and remove. There may be some adhesive glue holding down the old battery so you may need to gently pry the old battery up.

6. Insert the new Garmin Nuvi 765T battery. There is only one way to put the new battery in – the red wire will face the top. Now reconnect the battery (and if you disconnected the speaker then reconnect the speaker cable).

7. Now close the housing being careful to not pinch the wires. Click the housing together.

8. Now screw the 2 screws back on place using the T4.

9. Charge your new battery for 4 hours and then turn on to use your Garmin Nuvi 765T.  

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

Garmin Nuvi 760T Battery Installation Instructions

The following Garmin Nuvi 760T Battery Replacement Instruction guide can be used for the following models:

Garmin Nuvi 760T Battery

1. Begin by turning your nuvi 760T face down.

2. On the back near the bottom there will be 2 small screws. Remove those screws with the T4 screw driver provided.

3. Next using the pry tool provided separate the housing case being sure to separate all around the Garmin.

4. Lift up the front portion of the nuvi being careful not to fully separate the two parts as the battery connector and the speaker connector will be attached and connected. Lift just enough to see the battery and the connectors.

(At this point you have 2 options at this point – either disconnect both the speaker wire connector and the battery connector to full separate both halves or simply disconnect the battery cable. You can do whatever is easier for you.)

5. Now disconnect the old battery and remove. There may be some adhesive glue holding down the old battery so you may need to gently pry the old battery up.

6. Insert the new Garmin Nuvi 760T battery. There is only one way to put the new battery in – the red wire will face the top. Now reconnect the battery (and if you disconnected the speaker then reconnect the speaker cable).

7. Now close the housing being careful to not pinch the wires. Click the housing together.

8. Now screw the 2 screws back on place using the T4.

9. Charge your new battery for 4 hours and then turn on to use your Garmin Nuvi 760T. 

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

Garmin Nuvi 760 Battery Installation Instructions

The following Garmin Nuvi 760 Battery Replacement Instruction guide can be used for the following models:

Garmin Nuvi 760 Battery

1. Begin by turning your nuvi 760 face down.

2. On the back near the bottom there will be 2 small screws. Remove those screws with the T4 screw driver provided.

3. Next using the pry tool provided separate the housing case being sure to separate all around the Garmin.

4. Lift up the front portion of the nuvi being careful not to fully separate the two parts as the battery connector and the speaker connector will be attached and connected. Lift just enough to see the battery and the connectors.

(At this point you have 2 options at this point – either disconnect both the speaker wire connector and the battery connector to full separate both halves or simply disconnect the battery cable. You can do whatever is easier for you.)

5. Now disconnect the old battery and remove. There may be some adhesive glue holding down the old battery so you may need to gently pry the old battery up.

6. Insert the new Garmin Nuvi 760 battery. There is only one way to put the new battery in – the red wire will face the top. Now reconnect the battery (and if you disconnected the speaker then reconnect the speaker cable).

7. Now close the housing being careful to not pinch the wires. Click the housing together.

8. Now screw the 2 screws back on place using the T4.

9. Charge your new battery for 4 hours and then turn on to use your Garmin Nuvi 760. 
 PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

Garmin Nuvi 750 Battery Installation Instructions

The following Garmin Nuvi 750 Battery Replacement Instruction guide can be used for the following models:

Garmin Nuvi 750 Battery

1. Begin by turning your nuvi 750 face down.

2. On the back near the bottom there will be 2 small screws. Remove those screws with the T4 screw driver provided.

3. Next using the pry tool provided separate the housing case being sure to separate all around the Garmin.

4. Lift up the front portion of the nuvi being careful not to fully separate the two parts as the battery connector and the speaker connector will be attached and connected. Lift just enough to see the battery and the connectors.

(At this point you have 2 options at this point – either disconnect both the speaker wire connector and the battery connector to full separate both halves or simply disconnect the battery cable. You can do whatever is easier for you.)

5. Now disconnect the old battery and remove. There may be some adhesive glue holding down the old battery so you may need to gently pry the old battery up.

6. Insert the new Garmin Nuvi 750 battery. There is only one way to put the new battery in – the red wire will face the top. Now reconnect the battery (and if you disconnected the speaker then reconnect the speaker cable).

7. Now close the housing being careful to not pinch the wires. Click the housing together.

8. Now screw the 2 screws back on place using the T4.

9. Charge your new battery for 4 hours and then turn on to use your Garmin Nuvi 750.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

Garmin Nuvi 360 Battery Installation Instructions

The following Garmin Nuvi 360 Battery Replacement Instruction guide can be used for the following models:

Garmin Nuvi 360 Battery

1. Begin by lifting up your GPS receiver.

2. Then remove the 2 screws on the back of your receiver.

3. Pry open your receiver and locate the black plastic spring at the base of the receiver. Using a sharp object press into the spring cover and press inward on the spring towards the center in order to release the spring that secures the receiver. Remove the spring and unfasten he receiver to reveal 2 screws.

4. Remove the 2 screws that were hidden by the receiver.

5. Now separate the Garmin by prying around your Garmin removing the screen off the back of your Garmin 360.

6. Carefully open the Garmin and detach the yellow ribbon cable near the side of the Garmin. This cable connects to your receiver. Once disconnected you can you can pull the yellow ribbon cable out to make working with the Garmin a little easier.

7. Lift the upper portion of the Garmin to reveal a screw securing the circuit board. Unscrew the screw in order to lift the circuit board.

8. Lift the circuit board and then detach the battery cable from the circuit board.

9. Pry off the original battery replace the battery with a new Garmin Nuvi 360 GPS Battery from Batteryship.com.

10. Connect the new battery to the circuit board.

11. Return the circuit board to its original position and securely fasten the circuit board screw.

12. Return the yellow ribbon cable to its original place and reattach the ribbon cable.

13. Snap the Garmin shut.

14. Replace the 2 screws you removed that were hidden by the receiver.

15. Now return the receiver spring back to the base of the receiver (its original position) and snap the receiver in place.

16. Replace the screws on the back of the receiver and fold down the receiver.

17. Charge your new battery for 4 hours and then turn on to use your Garmin 360.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

Palm Zire 72 Battery Installation Instructions

The following Palm Zire 72 Battery Replacement Instruction guide can be used for the following models:

Palm Zire 72 Battery

1. Sync – sync the Palm to your desktop before doing anything.

2. Remove the Screws – Use a T5 Torx screwdriver to remove the two screws visible at the bottom rear of the Zire 72. Another screw is hidden under the adhesive label on the back. With effort, you can peel this label off (start at the upper left). Instead of peeling the whole label you can also choose to cut the portion of the label covering the screw, permanently exposing the small screw but leaving the rest of the label untouched. The screw is at the upper edge of the label, right underneath the upper left corner of the bluetooth icon. This screw holds down a tab of the mesh screen that surrounds the camera. Once exposed, remove this screw with a very small Phillips screwdriver.

3. Remove the Mesh – You can now gently pry up and remove the mesh. It has a press fit along its upper edge. Underneath the mesh are two more Phillips head screws. Remove these.

4. Pry the Case Open  – Next separate the two halves of the case along a line that goes along the back side of the stylus silo, the front side of the black bezel around the expansion card slot, and around the other two sides (the fit is incredibly tight. I had to use multiple small screwdrivers to pry the case open, and could not avoid bending some metal. Once the sides are separated, open up the case. Be careful; the two halves are connected by two delicate cables, which you may want to unplug. One is a ribbon cable that goes to the camera.

5. Replace the Battery You will see the battery and its tiny connector to the board. Remove the connector (you can use plastic tweezers if needed), remember which side the red wire is on.  The old battery is firmly glued down on its back side. Pry the battery up to release it. Then insert the new battery and attach the connector. Some double-sided tape will help hold the battery in place while you reassemble the unit.

6. Reassemble – Snap the case back together. The tiny clear plastic "light indicator" that relays the green power light to the outside of the case needs to be properly positioned, if it has gotten loose. It has 2 registration holes which need to be placed carefully over the 2 registration pins inside the top of the Zire case on the side opposite the stylus. The curved shoulder of this plastic piece needs to be on the side of the curved shoulder of the Zire.

Then replace the screws and mesh. If you peeled back the label, find a way to glue it down again.

Your new battery should be charged for 3 hours before using the Palm. Then do a hard reset by holding the power button, pressing the tiny reset button in the hole on the back, waiting for the Palm Powered logo, and then releasing the power button. Confirm the hard reset and continue to follow instructions to set up and sync your device.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.