Battery Education

Garmin Nuvi 1490T Battery Installation Instructions

The following Garmin Nuvi 1490T Battery Replacement Instruction guide can be used for the:

1. To begin use the pry tool to remove the Nuvi's primary faceplate. Slide the prytool in the groove around the outside edges of the faceplate (this is the black cover that goes around the face of the nuvi to protect the screen if you lay the nuvi face down). When done you will see 4 screws (1 on each the 4 corners).

2. Remove the four screws using the torx provided in your Kit from BatteryShip.com.

3. Once the screw are removed, remove the Garmin's secondary faceplate by running the pry tool around the edge of the Garmin. This will separate the 2 halves.

4. Next slowly and carefully pull your Garmin screen up and forward. Do not completely separate the 2 halves as a ribbon cable is attached on and connects both sides (this is what powers and controls you screen).

4. Next you will need to lift up the circuit board. To do this you have to remove the 2 screws that hold the circuit board in place. Use the tools that came in your kit to remove the 2 screws securing the circuit board.

5. Once the circuit board screws are removed carefully lift the circuit board so that you can access the battery connector. Hint: as you remove the screws of the circuit board you will see the batter. Garmin designed the circuit board so that the battery connector would have to be connected on the bottom of the board. So once you lift the board up a little you will be able to grab the battery cable and disconnect the battery from the circuit board.

6. Next pry the original battery up.

7. Replace the original Garmin Nuvi 1490T Battery with one from BatteryShip.com and connect
the new battery back to the circuit board.

8. Replace the circuit board to its original position and screw the circuit board back in place.

9. Return the screen back to its original position and attach the secondary faceplate to the screen.

10. Replace the 4 screws around the 4 corners of the Garmin.

11. Replace the primary faceplate by securely snapping in the plate all the way around the Nuvi.

12. Charge your new Garmin Nuvi 1490T Battery for 4 hours and then turn on.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are
required for the successful replacement of a battery. Excessive force may result in damage
to your device. The instructions above come with no warranty or guarantee. By utilizing
these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless
and unaccountable for any and all damages, problems, or personal injuries that may or may
not arise by your use of these instructions. Replacing your battery may void any warranty
you have on your device. Please read all instructions BEFORE replacing the battery.

Garmin Nuvi 1490 Battery Installation Instructions

The following Garmin Nuvi 1490 Battery Replacement Instruction guide can be used for the:

1. To begin use the pry tool to remove the Nuvi's primary faceplate. Slide the prytool in the groove around the outside edges of the faceplate (this is the black cover that goes around the face of the nuvi to protect the screen if you lay the nuvi face down). When done you will see 4 screws (1 on each the 4 corners).

2. Remove the four screws using the torx provided in your Kit from BatteryShip.com.

3. Once the screw are removed, remove the Garmin's secondary faceplate by running the pry tool around the edge of the Garmin. This will separate the 2 halves.

4. Next slowly and carefully pull your Garmin screen up and forward. Do not completely separate the 2 halves as a ribbon cable is attached on and connects both sides (this is what powers and controls you screen).

4. Next you will need to lift up the circuit board. To do this you have to remove the 2 screws that hold the circuit board in place. Use the tools that came in your kit to remove the 2 screws securing the circuit board.

5. Once the circuit board screws are removed carefully lift the circuit board so that you can access the battery connector. Hint: as you remove the screws of the circuit board you will see the batter. Garmin designed the circuit board so that the battery connector would have to be connected on the bottom of the board. So once you lift the board up a little you will be able to grab the battery cable and disconnect the battery from the circuit board.

6. Next pry the original battery up.

7. Replace the original Garmin Nuvi 1490 Battery with one from BatteryShip.com and connect
the new battery back to the circuit board.

8. Replace the circuit board to its original position and screw the circuit board back in place.

9. Return the screen back to its original position and attach the secondary faceplate to the screen.

10. Replace the 4 screws around the 4 corners of the Garmin.

11. Replace the primary faceplate by securely snapping in the plate all the way around the Nuvi.

12. Charge your new Garmin Nuvi 1490 Battery for 4 hours and then turn on.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are
required for the successful replacement of a battery. Excessive force may result in damage
to your device. The instructions above come with no warranty or guarantee. By utilizing
these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless
and unaccountable for any and all damages, problems, or personal injuries that may or may
not arise by your use of these instructions. Replacing your battery may void any warranty
you have on your device. Please read all instructions BEFORE replacing the battery.

Garmin Nuvi 1450 Battery Installation Instructions

The following Garmin Nuvi 1450 Battery Replacement Instruction guide can be used for the:

1. To begin use the pry tool to remove the Nuvi's primary faceplate. Slide the prytool in the groove around the outside edges of the faceplate (this is the black cover that goes around the face of the nuvi to protect the screen if you lay the nuvi face down). When done you will see 4 screws (1 on each the 4 corners).

2. Remove the four screws using the torx provided in your Kit from BatteryShip.com.

3. Once the screw are removed, remove the Garmin's secondary faceplate by running the pry tool around the edge of the Garmin. This will separate the 2 halves.

4. Next slowly and carefully pull your Garmin screen up and forward. Do not completely separate the 2 halves as a ribbon cable is attached on and connects both sides (this is what powers and controls you screen).

4. Next you will need to lift up the circuit board. To do this you have to remove the 2 screws that hold the circuit board in place. Use the tools that came in your kit to remove the 2 screws securing the circuit board.

5. Once the circuit board screws are removed carefully lift the circuit board so that you can access the battery connector. Hint: as you remove the screws of the circuit board you will see the batter. Garmin designed the circuit board so that the battery connector would have to be connected on the bottom of the board. So once you lift the board up a little you will be able to grab the battery cable and disconnect the battery from the circuit board.

6. Next pry the original battery up.

7. Replace the original Garmin Nuvi 1450 Battery with one from BatteryShip.com and connect
the new battery back to the circuit board.

8. Replace the circuit board to its original position and screw the circuit board back in place.

9. Return the screen back to its original position and attach the secondary faceplate to the screen.

10. Replace the 4 screws around the 4 corners of the Garmin.

11. Replace the primary faceplate by securely snapping in the plate all the way around the Nuvi.

12. Charge your new Garmin Nuvi 1450 Battery for 4 hours and then turn on.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are
required for the successful replacement of a battery. Excessive force may result in damage
to your device. The instructions above come with no warranty or guarantee. By utilizing
these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless
and unaccountable for any and all damages, problems, or personal injuries that may or may
not arise by your use of these instructions. Replacing your battery may void any warranty
you have on your device. Please read all instructions BEFORE replacing the battery.

Garmin Nuvi 1400 Battery Installation Instructions

The following Garmin Nuvi 1400 Battery Replacement Instruction guide can be used for the:

1. To begin use the pry tool to remove the Nuvi's primary faceplate. Slide the prytool in the groove around the outside edges of the faceplate (this is the black cover that goes around the face of the nuvi to protect the screen if you lay the nuvi face down). When done you will see 4 screws (1 on each the 4 corners).

2. Remove the four screws using the torx provided in your Kit from BatteryShip.com.

3. Once the screw are removed, remove the Garmin's secondary faceplate by running the pry tool around the edge of the Garmin. This will separate the 2 halves.

4. Next slowly and carefully pull your Garmin screen up and forward. Do not completely separate the 2 halves as a ribbon cable is attached on and connects both sides (this is what powers and controls you screen).

4. Next you will need to lift up the circuit board. To do this you have to remove the 2 screws that hold the circuit board in place. Use the tools that came in your kit to remove the 2 screws securing the circuit board.

5. Once the circuit board screws are removed carefully lift the circuit board so that you can access the battery connector. Hint: as you remove the screws of the circuit board you will see the batter. Garmin designed the circuit board so that the battery connector would have to be connected on the bottom of the board. So once you lift the board up a little you will be able to grab the battery cable and disconnect the battery from the circuit board.

6. Next pry the original battery up.

7. Replace the original Garmin Nuvi 1400 Battery with one from BatteryShip.com and connect
the new battery back to the circuit board.

8. Replace the circuit board to its original position and screw the circuit board back in place.

9. Return the screen back to its original position and attach the secondary faceplate to the screen.

10. Replace the 4 screws around the 4 corners of the Garmin.

11. Replace the primary faceplate by securely snapping in the plate all the way around the Nuvi.

12. Charge your new Garmin Nuvi 1400 Battery for 4 hours and then turn on.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are
required for the successful replacement of a battery. Excessive force may result in damage
to your device. The instructions above come with no warranty or guarantee. By utilizing
these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless
and unaccountable for any and all damages, problems, or personal injuries that may or may
not arise by your use of these instructions. Replacing your battery may void any warranty
you have on your device. Please read all instructions BEFORE replacing the battery.

Magellan Maestro 4220 Battery Installation Instructions

The following Magellan Maestro 4220 Battery Replacement Instruction guide can be used for the:

Magellan Maestro 4220

1. To begin turn your Magellan Maestro 4220 over and remove the 4 rubber caps to reveal the 4 four screws.

2. Remove the four screws on the back.

3. Using the pry tool carefully pry apart the front of the device.

4. Disconnect the ribbon cable by prying up the plastic retainer.

5. Remove the 2 screws securing the circuit board.

6.Pry off the circuit board gently.

7. Pry the original battery up and disconnect the original battery.

8. Replace the original Magellan Maestro 4220 Battery with one from BatteryShip.com and connect the new battery.

9. Replace the circuit board and screw the circuit board back in place.

10. Connect the front cover to the circuit board.

11. Close the case and turn the Magellan Maestro 4220 over on its face.

12. Replace the 4 screws and the rubber caps.

13. Charge your new Magellan Maestro 4220 Battery for 4 hours.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

Magellan Maestro 4210 Battery Installation Instructions

The following Magellan Maestro 4210 Battery Replacement Instruction guide can be used for the:

Magellan Maestro 4210

1. To begin turn your Magellan Maestro 4210 over and remove the 4 rubber caps to reveal the 4 four screws.

2. Remove the four screws on the back.

3. Using the pry tool carefully pry apart the front of the device.

4. Disconnect the ribbon cable by prying up the plastic retainer.

5. Remove the 2 screws securing the circuit board.

6.Pry off the circuit board gently.

7. Pry the original battery up and disconnect the original battery.

8. Replace the original Magellan Maestro 4210 Battery with one from BatteryShip.com and connect the new battery.

9. Replace the circuit board and screw the circuit board back in place.

10. Connect the front cover to the circuit board.

11. Close the case and turn the Magellan Maestro 4210 over on its face.

12. Replace the 4 screws and the rubber caps.

13. Charge your new Magellan Maestro 4210 Battery for 4 hours.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

Magellan Maestro 4200 Battery Installation Instructions

The following Magellan Maestro 4200 Battery Replacement Instruction guide can be used for the:

Magellan Maestro 4200

1. To begin turn your Magellan Maestro 4200 over and remove the 4 rubber caps to reveal the 4 four screws.

2. Remove the four screws on the back.

3. Using the pry tool carefully pry apart the front of the device.

4. Disconnect the ribbon cable by prying up the plastic retainer.

5. Remove the 2 screws securing the circuit board.

6.Pry off the circuit board gently.

7. Pry the original battery up and disconnect the original battery.

8. Replace the original Magellan Maestro 4200 Battery with one from BatteryShip.com and connect the new battery.

9. Replace the circuit board and screw the circuit board back in place.

10. Connect the front cover to the circuit board.

11. Close the case and turn the Magellan Maestro 4200 over on its face.

12. Replace the 4 screws and the rubber caps.

13. Charge your new Magellan Maestro 4200 Battery for 4 hours.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

Garmin Nuvi 700 Battery Installation Instructions

The following Garmin Nuvi 700 Battery Replacement Instruction guide can be used for the following models:

Garmin Nuvi 700 Battery

1. Begin by turning your nuvi 700 face down.

2. On the back near the bottom there will be 2 small screws. Remove those screws with the T4 screw driver provided.

3. Next using the pry tool provided separate the housing case being sure to separate all around the Garmin.

4. Lift up the front portion of the nuvi being careful not to fully separate the two parts as the battery connector and the speaker connector will be attached and connected. Lift just enough to see the battery and the connectors.

(At this point you have 2 options at this point - either disconnect both the speaker wire connector and the battery connector to full separate both halves or simply disconnect the battery cable. You can do whatever is easier for you.)

5. Now disconnect the old battery and remove. There may be some adhesive glue holding down the old battery so you may need to gently pry the old battery up.

6. Insert the new Garmin Nuvi 700 battery. There is only one way to put the new battery in - the red wire will face the top. Now reconnect the battery (and if you disconnected the speaker then reconnect the speaker cable).

7. Now close the housing being careful to not pinch the wires. Click the housing together.

8. Now screw the 2 screws back on place using the T4.

9. Charge your new battery for 4 hours and then turn on to use your Garmin Nuvi 700.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

TomTom One 130S Battery Replacement Instructions

The following TomTom One 130 S Battery Replacement Instruction guide can be used for the following models:

TomTom One 130S Battery

1. Begin by removing the faceplate to reveal four screws. To remove the faceplate use the pry tool to lift the face plate up.

2. Remove the four screws using your screw drivers included in your tool kit.

3. Next carefully lift the screen mount plate and rubber shield around the screen off your screen. Lifting from the base of the screen will help accomplish this. Use your pry tool to accomplish this.

4. To access the battery you will need to remove the three screws securing the TomTom's circuit board. One of the screws is under the screen's ribbon cable.

5. Once the circuit board screws are removed you will be able to carefully lift the circuit board and disconnect the battery cable from the board.

6. Once the battery cable is disconnected you can gently pry out the original battery.

7. Connect the new TomTom One 130S Battery and place into the battery compartment (where you took the original out of). It would be helpful to secure the new battery with a strip of double sided tape.

8. Replace the circuit board to its original position and replace the circuit board screws.

9. Replace the screen on top of the circuit board.

10. Replace the screen shield and the screen mount plate around and onto of the screen.

11. Replace the 4 screws you removed in step 2.

12. Attach the faceplate of your TomTom.

13. Charge your battery for a four hours. Then turn on your TomTom.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

TomTom XXL IQ Battery Replacement Instructions

The following TomTom One Battery Replacement Instruction guide can be used for the following models:

TomTom XXL IQ Battery

1. Begin by lifting the ends of the label up off your TomTom (this will be on the bottom). You can use the prytool that comes in the kit to do this. The 2 screws are under the ends of the label (one screw under each end).

2. Remove the screws using your torx drivers included in your tool kit.

3. Once the two screws are removed taky your pry tool and insert between the two halves of the Tom Tom and run it around the edge of the TomTom to help separate the two sides. Once you work all the way around the TomTom you will be able to separate the two halves. Please be careful to not pull the two sides to far apart as they are connected by a ribbon cable on the inside. This ribbon cable does not need to be removed to see the battery.

4. In order to gain access to the battery you must remove the three screws securing the circuit board.

5 Once the screws are removed you will be able to carefully lift the circuit board and disconnect the battery cable to the board.

6. Once the battery cable is disconnected you can pry out the original battery.

7. Connect the new TomTom XXL IQ Battery and place into the battery compartment (where you took the original out of).

8. Replace the circuit board and screws.

9. Then put the two halves together. The two sides will snap gently into place.

10. Replace the 2 screws you removed in step 2 and smooth down the label.

11. Charge your battery for a four hours. Then turn on your TomTom.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.