Battery Education

Sony PRS-505-LC Battery Replacement Instructions

The following are the Sony PRS-505-LC Battery Replacement Instruction guide.

1. Begin by laying your Sony face down so that the backside is facing you.

2. Next remove the 4 screws located on the back of your device (near all 4 corners of the
device)

3. Next - on the bottom of the eReader there will be a screw near the corner (opposite of
the input/connector slots). Loosen this screw. The screw will remain connected to the
reader but it does need to be loosened in order to separate the 2 halves.

4. Now using the pry tool provided in your kit gently remove the bottom external frame
(this is the metal frame that covers the input slots).

5. Once the metal cover has been removed you will see 3 screws. Remove these screws. Next
remove the back cover to reveal the inside of your Sony and the battery.

6. Next turn the eReader over and remove any SD Cards from the device.

7. Once the SD Cards are removed then using the pry tool remove the metal frame that covers
the SD Slots.

8. Next using the flat head screwdriver provided lift off the 2 clips from the top of the
device.

9. Turn the eReader over and use the pry tool to push out the eReader from its cover. Push
it out just far enough so that you can access the ribbon cable.

10. Disconnect Ribbon cable.

11. Then pull the internal part of eReader out of its frame until you can see the battery.

12. Use the pry tool to lift up the old battery and disconnect it and remove from the
battery compartment.

13. Replace the old battery with a brand new Sony PRS-505-LC Battery Replacement from

BatteryShip.com. When replacing the battery be sure to push down the battery cables below the

circuit board surface.

14. Now let's reverse our steps. Carefully push back in the internal portion iof eReader
back into the frame. Only go half way since we need to reconnect the ribbon cable.

15. Connect the ribbon cable. Be sure it is secure.

16. Continue pushing in the eReader till it is back in position.

17. Return the 2 clips to their original positions.

18. Replace the top metal frame cover.

19. Return the 3 screws to the bottom of the device.

20. Snap the bottom metal frame cover in place and tighten the screw to secure the frame
into place.

21. Insert any SD cards back into their respective slots and replace the 4 screws on the
back of the eReader.

22. Charge your Sony PRS-505-LC Battery for four hours. Then turn on your Sony.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

Sony PRS-505-SC Battery Replacement Instructions

The following are the Sony PRS-505-SC Battery Replacement Instruction guide.

1. Begin by laying your Sony face down so that the backside is facing you.

2. Next remove the 4 screws located on the back of your device (near all 4 corners of the
device)

3. Next - on the bottom of the eReader there will be a screw near the corner (opposite of
the input/connector slots). Loosen this screw. The screw will remain connected to the
reader but it does need to be loosened in order to separate the 2 halves.

4. Now using the pry tool provided in your kit gently remove the bottom external frame
(this is the metal frame that covers the input slots).

5. Once the metal cover has been removed you will see 3 screws. Remove these screws. Next
remove the back cover to reveal the inside of your Sony and the battery.

6. Next turn the eReader over and remove any SD Cards from the device.

7. Once the SD Cards are removed then using the pry tool remove the metal frame that covers
the SD Slots.

8. Next using the flat head screwdriver provided lift off the 2 clips from the top of the
device.

9. Turn the eReader over and use the pry tool to push out the eReader from its cover. Push
it out just far enough so that you can access the ribbon cable.

10. Disconnect Ribbon cable.

11. Then pull the internal part of eReader out of its frame until you can see the battery.

12. Use the pry tool to lift up the old battery and disconnect it and remove from the
battery compartment.

13. Replace the old battery with a brand new Sony PRS-505-SC Battery Replacement from BatteryShip.com. When replacing the battery be sure to push down the battery cables below the circuit board surface.

14. Now let's reverse our steps. Carefully push back in the internal portion iof eReader
back into the frame. Only go half way since we need to reconnect the ribbon cable.

15. Connect the ribbon cable. Be sure it is secure.

16. Continue pushing in the eReader till it is back in position.

17. Return the 2 clips to their original positions.

18. Replace the top metal frame cover.

19. Return the 3 screws to the bottom of the device.

20. Snap the bottom metal frame cover in place and tighten the screw to secure the frame
into place.

21. Insert any SD cards back into their respective slots and replace the 4 screws on the
back of the eReader.

22. Charge your Sony PRS-505-SC Battery for four hours. Then turn on your Sony.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

Sony PRS-505-RC Battery Replacement Instructions

The following are the Sony PRS-505-RC Battery Replacement Instruction guide.

1. Begin by laying your Sony face down so that the backside is facing you.

2. Next remove the 4 screws located on the back of your device (near all 4 corners of the
device)

3. Next - on the bottom of the eReader there will be a screw near the corner (opposite of the input/connector slots). Loosen this screw. The screw will remain connected to the
reader but it does need to be loosened in order to separate the 2 halves.

4. Now using the pry tool provided in your kit gently remove the bottom external frame
(this is the metal frame that covers the input slots).

5. Once the metal cover has been removed you will see 3 screws. Remove these screws. Next
remove the back cover to reveal the inside of your Sony and the battery.

6. Next turn the eReader over and remove any SD Cards from the device.

7. Once the SD Cards are removed then using the pry tool remove the metal frame that covers
the SD Slots.

8. Next using the flat head screwdriver provided lift off the 2 clips from the top of the
device.

9. Turn the eReader over and use the pry tool to push out the eReader from its cover. Push
it out just far enough so that you can access the ribbon cable.

10. Disconnect Ribbon cable.

11. Then pull the internal part of eReader out of its frame until you can see the battery.

12. Use the pry tool to lift up the old battery and disconnect it and remove from the
battery compartment.

13. Replace the old battery with a brand new Sony PRS-505-RC Battery Replacement from BatteryShip.com. When replacing the battery be sure to push down the battery cables below the circuit board surface.

14. Now let's reverse our steps. Carefully push back in the internal portion iof eReader
back into the frame. Only go half way since we need to reconnect the ribbon cable.

15. Connect the ribbon cable. Be sure it is secure.

16. Continue pushing in the eReader till it is back in position.

17. Return the 2 clips to their original positions.

18. Replace the top metal frame cover.

19. Return the 3 screws to the bottom of the device.

20. Snap the bottom metal frame cover in place and tighten the screw to secure the frame
into place.

21. Insert any SD cards back into their respective slots and replace the 4 screws on the
back of the eReader.

22. Charge your Sony PRS-505-RC Battery for four hours. Then turn on your Sony.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

Sony PRS-505SC-JP Battery Replacement Instructions

The following are the Sony PRS-505SC-JP Battery Replacement Instruction guide.

1. Begin by laying your Sony face down so that the backside is facing you.

2. Next remove the 4 screws located on the back of your device (near all 4 corners of the
device).

3. Next - on the bottom of the eReader there will be a screw near the corner (opposite of the input/connector slots). Loosen this screw. The screw will remain connected to the reader but it does need to be loosened in order to separate the 2 halves.

4. Now using the pry tool provided in your kit gently remove the bottom external frame
(this is the metal frame that covers the input slots).

5. Once the metal cover has been removed you will see 3 screws. Remove these screws. Next
remove the back cover to reveal the inside of your Sony and the battery.

6. Next turn the eReader over and remove any SD Cards from the device.

7. Once the SD Cards are removed then using the pry tool remove the metal frame that covers
the SD Slots.

8. Next using the flat head screwdriver provided lift off the 2 clips from the top of the
device.

9. Turn the eReader over and use the pry tool to push out the eReader from its cover. Push
it out just far enough so that you can access the ribbon cable.

10. Disconnect Ribbon cable.

11. Then pull the internal part of eReader out of its frame until you can see the battery.

12. Use the pry tool to lift up the old battery and disconnect it and remove from the
battery compartment.

13. Replace the old battery with a brand new Sony PRS-505SC-JP Battery Replacement from BatteryShip.com. When replacing the battery be sure to push down the battery cables below the circuit board surface.

14. Now let's reverse our steps. Carefully push back in the internal portion iof eReader back into the frame. Only go half way since we need to reconnect the ribbon cable.

15. Connect the ribbon cable. Be sure it is secure.

16. Continue pushing in the eReader till it is back in position.

17. Return the 2 clips to their original positions.

18. Replace the top metal frame cover.

19. Return the 3 screws to the bottom of the device.

20. Snap the bottom metal frame cover in place and tighten the screw to secure the frame
into place.

21. Insert any SD cards back into their respective slots and replace the 4 screws on the
back of the eReader.

22. Charge your Sony PRS-505SC-JP Battery for four hours. Then turn on your Sony.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

Sony PRS-505 Battery Replacement Instructions

The following are the Sony PRS-505 Battery Replacement Instruction guide.

1. Begin by laying your Sony face down so that the backside is facing you.

2. Next remove the 4 screws located on the back of your device (near all 4 corners of the
device)

3. Next - on the bottom of the eReader there will be a screw near the corner (opposite of
the input/connector slots). Loosen this screw. The screw will remain connected to the
reader but it does need to be loosened in order to separate the 2 halves.

4. Now using the pry tool provided in your kit gently remove the bottom external frame
(this is the metal frame that covers the input slots).

5. Once the metal cover has been removed you will see 3 screws. Remove these screws. Next
remove the back cover to reveal the inside of your Sony and the battery.

6. Next turn the eReader over and remove any SD Cards from the device.

7. Once the SD Cards are removed then using the pry tool remove the metal frame that covers
the SD Slots.

8. Next using the flat head screwdriver provided lift off the 2 clips from the top of the
device.

9. Turn the eReader over and use the pry tool to push out the eReader from its cover. Push
it out just far enough so that you can access the ribbon cable.

10. Disconnect Ribbon cable.

11. Then pull the internal part of eReader out of its frame until you can see the battery.

12. Use the pry tool to lift up the old battery and disconnect it and remove from the
battery compartment.

13. Replace the old battery with a brand new Sony PRS-505 Battery Replacement. When
replacing the battery be sure to push down the battery cables below the circuit board
surface.

14. Now let's reverse our steps. Carefully push back in the internal portion iof eReader
back into the frame. Only go half way since we need to reconnect the ribbon cable.

15. Connect the ribbon cable. Be sure it is secure.

16. Continue pushing in the eReader till it is back in position.

17. Return the 2 clips to their original positions.

18. Replace the top metal frame cover.

19. Return the 3 screws to the bottom of the device.

20. Snap the bottom metal frame cover in place and tighten the screw to secure the frame
into place.

21. Insert any SD cards back into their respective slots and replace the 4 screws on the
back of the eReader.

22. Charge your Sony PRS-505 Battery for four hours. Then turn on your Sony.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

Amazon Kindle 3 Battery Replacement Instructions

The following battery replacement instruction guide can be used for the following models:

Amazon Kindle 3 Battery

1. Begin by turning your Amazon Kindle 3 face down. Placing your Kindle 3 on a soft cloth will help prevent the screen from being scratched.

2. Using your pry tool pry off back cover by detatching the clips that holds the cover on. You will need to slide the pry tool around the entire back cover. After the clips have been detached slide the cover downward and the cover will then come off.

3. Once the back cover is off you will see the inside of the Kindle and the battery.

4. Next remove the 2 screws securing the battery.

5. Remove the original battery.

6. Replace the original battery with the your new Amazon Kindle 3 Battery Replacement from BatteryShip.com

7. Replace the two screws to secure the battery.

8. Replace the cover and snap into place. You will need to be sure to snap the cover in completely.

9. Charge your new Kindle 3 Battery for at least 4 hours. Then turn on and use.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

Amazon Kindle 2 Battery Replacement Instructions

The following battery replacement instruction guide can be used for the following models:

Amazon Kindle 2 Battery

1. Begin by turning your Amazon Kindle 2 face down. Placing your Kindle 2 on a soft cloth will help prevent the screen from being scratched.

2. Using your pry tool pry off the upper grey portion of the Kindle to reveal 2 small screws.

3. Once the upper portion is removed you will see two small screws on either side of the Kindle at the base of the cover. Please remove the screws.

4. Next use the pry tool to press down on the two plastic clips to release the cover. Once the clips are pressed down, lift off the cover to reveal the battery.

5. Remove the two screws securing the battery. Then using the prytool lift up the original battery.

6. Replace the original battery with the your new Amazon Kindle 2 Battery Replacement from BatteryShip.com

7. Replace the two screws to secure the battery.

8. Replace the cover and snap into place.

9. Return the two screws to hold the cover into place.

10. Return the upper grey portion of the Kindle.

11. Charge your new Kindle 2 Battery for at least 4 hours. Then turn on and use.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

Amazon Kindle 1 Battery Replacement Instructions

The following battery replacement instruction guide can be used for the following models:

Amazon Kindle 1 Battery

1. Begin by turning your Amazon Kindle 1 face down.

2. Slide the grey back cover off of the Kindle.

3. Gently lift the original battery out of the battery compartment and disconnect.

4. Place in the new Amazon Kindle 1 battery replacement and connect it to the battery connector.

5. Replace the grey back cover.

6. Charge your Amazon Kindle 1 for 4 hours.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

Garmin Edge 605 Battery Replacement Instructions

The following Garmin Edge 605 Battery Replacement Instruction guide can be used for the following models:

Garmin Edge 605 Battery and replacement kit

1. Begin by turning your Garmin face down and then remove the 6 screws on the back of your Garmin Edge 605.

2. Next using the pry tool carefully pry apart your Garmin casing using the shim/pry tool provided (this may take running the pry tool around the seams a couple of times but it will separate). Or you can grab both halves and carefully pull open. Do not pull completey apart as the battery cable is connected to circuit board.

3. Again as you open the 2 halves do not completely pull them apart as there will be connectors you will need to detach. One of the connectors is the battery connector. Remove the connector attached to the circuit board first. Then revovbe the battery connector. Once these connectors are detached you will be able to separate the 2 halves completely.

4. Now using the pry tool again remove the original battery (it is held down by an adhesive so pry with a gentle firmness)

5. Next place a piece of double sided tape in the battery compartment (this will hold down the battery so it does not move around on you)

6. Next place on the tape the new Garmin Edge 605 battery replacement.

7. Reconnect the connectors from step 3.

8. Next place the 2 sides together and gently snap the device shut (snap all the way around).

9. Next Replace the 6 screws you took out.

10. Next charge your Garmin Edge 705 for 4 hours.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

Sony PRS-600 Battery Replacement Instructions

The following Sony PRS-600 Battery Replacement Instruction guide can be used for the following models:

Sony PRS-600 Battery

1. Begin by laying your Sony face down so that the backside is facing you.

2. Next remove the two screws located on the back of your device.

3. Next detach the clip holding the back cover. Use your pry tool to help detach the clip. The clip is the the long back piece that runs the length of your Sony and is the piece held in by the 2 screws your just removed.

4. Next remove the back cover to reveal the inside of your Sony and the battery.

5. Remove the original battery and disconnect the battery cable from the circuit board. . The pry tool will help you lift the old battery out.

6. Replace and connect the new Sony PRS-600 Battery and place into the battery compartment (where you took the original out of).

7. Now let's reverse our steps. Replace the back cover so that it snaps in to the long back clip.

8. Replace the 2 screws on the clip.

9. Charge your battery for a four hours. Then turn on your Sony.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.