Battery Education

Garmin Nuvi 255W Battery Replacement Instructions

The following Garmin Nuvi 255W Battery Replacement Instruction guide can be used for the following models:

Garmin Nuvi 255W Battery

1. Garmin has hidden the first 2 screws underneath the Nuvi's label. Remove the lable to reveal the 2 screws.

2. Remove the two screws.

3. Using the pry tool sepearte the Garmin nuvi working your way around - this will release the power button cover - remove the button cover.

4. Remove the three screws securing the circuit board.

5. Carefully lift up the circuit board to reveal the battery's wire and connector.

6. Disconnect the original battery.

7. Use the pry tool to lift up the original battery. The original battery is held in place by an adhesive. After you remove the original battery you may need to add some more adhesive to hold your new battery in place. Double sided tap can do the trick.

8. Place the new Garmin Nuvi 255W battery from Batteryship.com into the battery compartment and connect the battery into the socket you removed the original from.

9. Replace the circuit board to its original position and screw back in.

10. Reposition the power button cover

11. Gently snap the device shut.

12. Screw the 2 screw back into the casing of the device.

13. Place the label back to its orginal postion to cover the 2 screws and charge the Nuvi for at least 4 hours.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

Garmin Nuvi 1260W Battery Installation Instructions

The following Garmin Nuvi 1260W Battery Replacement Instruction guide can be used for the following models:

Garmin Nuvi 1260W Battery

1. To begin remove the Garmin Nuvi 1260W faceplate using the prytool. Slide the prytool in between the grey faceplate and the rest of the Garmin. It will snap off once the tool slides all the way around.

2. Remove the 4 screws around each corner of the Garmin.

3. Carefully open the device. Use your prytool to help separate the Garmin in one corner then use your fingers to carefully pull apart the Garmin. Disconnect the old battery and lift up the battery.

4. Now gently lift the screen of the Garmin using your prytool. Please note that the screen is connected by a ribbon cable. So do not separate or pull the screen too hard or too far away from the Garmin as you could destroy the cable. As you do gently lift the screen you will see the battery. You only need to lift the screen enough to see and remove the old battery.

5. Disconnect the old battery. Using the prytool here may be helpful lifting the old battery out. The old battery will be glued with a light adhesive so gentle strength may need to be applied.

6. Place your your new Garmin Nuvi 1260W Battery and connect it.

7. Close up the Garmin screen.

8. Gently snap the Garmin shut and replace the 4 screws you recently removed in step 2.

9. Snap back on the Garmin's faceplate.

10. Charge your new Garmin Nuvi 1260W Battery for 4 hours and then turn on.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

Garmin Nuvi 1260 Battery Installation Instructions

The following Garmin Nuvi 1260 Battery Replacement Instruction guide can be used for the following models:

Garmin Nuvi 1260 Battery

1. To begin remove the Garmin Nuvi 1260 faceplate using the prytool. Slide the prytool in between the grey faceplate and the rest of the Garmin. It will snap off once the tool slides all the way around.

2. Remove the 4 screws around each corner of the Garmin.

3. Carefully open the device. Use your prytool to help separate the Garmin in one corner then use your fingers to carefully pull apart the Garmin. Disconnect the old battery and lift up the battery.

4. Now gently lift the screen of the Garmin using your prytool. Please note that the screen is connected by a ribbon cable. So do not separate or pull the screen too hard or too far away from the Garmin as you could destroy the cable. As you do gently lift the screen you will see the battery. You only need to lift the screen enough to see and remove the old battery.

5. Disconnect the old battery. Using the prytool here may be helpful lifting the old battery out. The old battery will be glued with a light adhesive so gentle strength may need to be applied.

6. Place your your new Garmin Nuvi 1260 Battery and connect it.

7. Close up the Garmin screen.

8. Gently snap the Garmin shut and replace the 4 screws you recently removed in step 2.

9. Snap back on the Garmin's faceplate.

10. Charge your new Garmin Nuvi 1260 Battery for 4 hours and then turn on.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

Garmin Nuvi 1255W Battery Installation Instructions

The following Garmin Nuvi 1255W Battery Replacement Instruction guide can be used for the following models:

Garmin Nuvi 1255W Battery

1. To begin remove the Garmin Nuvi 1255W faceplate using the prytool. Slide the prytool in between the grey faceplate and the rest of the Garmin. It will snap off once the tool slides all the way around.

2. Remove the 4 screws around each corner of the Garmin.

3. Carefully open the device. Use your prytool to help separate the Garmin in one corner then use your fingers to carefully pull apart the Garmin. Disconnect the old battery and lift up the battery.

4. Now gently lift the screen of the Garmin using your prytool. Please note that the screen is connected by a ribbon cable. So do not separate or pull the screen too hard or too far away from the Garmin as you could destroy the cable. As you do gently lift the screen you will see the battery. You only need to lift the screen enough to see and remove the old battery.

5. Disconnect the old battery. Using the prytool here may be helpful lifting the old battery out. The old battery will be glued with a light adhesive so gentle strength may need to be applied.

6. Place your your new Garmin Nuvi 1255W Battery and connect it.

7. Close up the Garmin screen.

8. Gently snap the Garmin shut and replace the 4 screws you recently removed in step 2.

9. Snap back on the Garmin's faceplate.

10. Charge your new Garmin Nuvi 1255W Battery for 4 hours and then turn on.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

Garmin Nuvi 1250T Battery Installation Instructions

The following Garmin Nuvi 1250T Battery Replacement Instruction guide can be used for the following models:

Garmin Nuvi 1250T Battery

1. To begin remove the Garmin Nuvi 1250T faceplate using the prytool. Slide the prytool in between the grey faceplate and the rest of the Garmin. It will snap off once the tool slides all the way around.

2. Remove the 4 screws around each corner of the Garmin.

3. Carefully open the device. Use your prytool to help separate the Garmin in one corner then use your fingers to carefully pull apart the Garmin. Disconnect the old battery and lift up the battery.

4. Now gently lift the screen of the Garmin using your prytool. Please note that the screen is connected by a ribbon cable. So do not separate or pull the screen too hard or too far away from the Garmin as you could destroy the cable. As you do gently lift the screen you will see the battery. You only need to lift the screen enough to see and remove the old battery.

5. Disconnect the old battery. Using the prytool here may be helpful lifting the old battery out. The old battery will be glued with a light adhesive so gentle strength may need to be applied.

6. Place your your new Garmin Nuvi 1250T Battery and connect it.

7. Close up the Garmin screen.

8. Gently snap the Garmin shut and replace the 4 screws you recently removed in step 2.

9. Snap back on the Garmin's faceplate.

10. Charge your new Garmin Nuvi 1250T Battery for 4 hours and then turn on.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

Garmin Nuvi 1250 Battery Installation Instructions

The following Garmin Nuvi 1250 Battery Replacement Instruction guide can be used for the following models:

Garmin Nuvi 1250 Battery

1. To begin remove the Garmin Nuvi 1250 faceplate using the prytool. Slide the prytool in between the grey faceplate and the rest of the Garmin. It will snap off once the tool slides all the way around.

2. Remove the 4 screws around each corner of the Garmin.

3. Carefully open the device. Use your prytool to help separate the Garmin in one corner then use your fingers to carefully pull apart the Garmin. Disconnect the old battery and lift up the battery.

4. Now gently lift the screen of the Garmin using your prytool. Please note that the screen is connected by a ribbon cable. So do not separate or pull the screen too hard or too far away from the Garmin as you could destroy the cable. As you do gently lift the screen you will see the battery. You only need to lift the screen enough to see and remove the old battery.

5. Disconnect the old battery. Using the prytool here may be helpful lifting the old battery out. The old battery will be glued with a light adhesive so gentle strength may need to be applied.

6. Place your your new Garmin Nuvi 1250 Battery and connect it.

7. Close up the Garmin screen.

8. Gently snap the Garmin shut and replace the 4 screws you recently removed in step 2.

9. Snap back on the Garmin's faceplate.

10. Charge your new Garmin Nuvi 1250 Battery for 4 hours and then turn on.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

Garmin Nuvi 1205W Battery Installation Instructions

The following Garmin Nuvi 1205W Battery Replacement Instruction guide can be used for the following models:

Garmin Nuvi 1205W Battery

1. To begin remove the Garmin Nuvi 1205W faceplate using the prytool. Slide the prytool in between the grey faceplate and the rest of the Garmin. It will snap off once the tool slides all the way around.

2. Remove the 4 screws around each corner of the Garmin.

3. Carefully open the device. Use your prytool to help separate the Garmin in one corner then use your fingers to carefully pull apart the Garmin. Disconnect the old battery and lift up the battery.

4. Now gently lift the screen of the Garmin using your prytool. Please note that the screen is connected by a ribbon cable. So do not separate or pull the screen too hard or too far away from the Garmin as you could destroy the cable. As you do gently lift the screen you will see the battery. You only need to lift the screen enough to see and remove the old battery.

5. Disconnect the old battery. Using the prytool here may be helpful lifting the old battery out. The old battery will be glued with a light adhesive so gentle strength may need to be applied.

6. Place your your new Garmin Nuvi 1205W Battery and connect it.

7. Close up the Garmin screen.

8. Gently snap the Garmin shut and replace the 4 screws you recently removed in step 2.

9. Snap back on the Garmin's faceplate.

10. Charge your new Garmin Nuvi 1205W Battery for 4 hours and then turn on.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

Garmin Nuvi 1205 Battery Installation Instructions

The following Garmin Nuvi 1205 Battery Replacement Instruction guide can be used for the following models:

Garmin Nuvi 1205 Battery

1. To begin remove the Garmin Nuvi 1205 faceplate using the prytool. Slide the prytool in between the grey faceplate and the rest of the Garmin. It will snap off once the tool slides all the way around.

2. Remove the 4 screws around each corner of the Garmin.

3. Carefully open the device. Use your prytool to help separate the Garmin in one corner then use your fingers to carefully pull apart the Garmin. Disconnect the old battery and lift up the battery.

4. Now gently lift the screen of the Garmin using your prytool. Please note that the screen is connected by a ribbon cable. So do not separate or pull the screen too hard or too far away from the Garmin as you could destroy the cable. As you do gently lift the screen you will see the battery. You only need to lift the screen enough to see and remove the old battery.

5. Disconnect the old battery. Using the prytool here may be helpful lifting the old battery out. The old battery will be glued with a light adhesive so gentle strength may need to be applied.

6. Place your your new Garmin Nuvi 1205 Battery and connect it.

7. Close up the Garmin screen.

8. Gently snap the Garmin shut and replace the 4 screws you recently removed in step 2.

9. Snap back on the Garmin's faceplate.

10. Charge your new Garmin Nuvi 1205 Battery for 4 hours and then turn on.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

Garmin Nuvi 1200 Battery Installation Instructions

The following Garmin Nuvi 1200 Battery Replacement Instruction guide can be used for the following models:

Garmin Nuvi 1200 Battery

1. To begin remove the Garmin Nuvi 1200 faceplate using the prytool. Slide the prytool in between the grey faceplate and the rest of the Garmin. It will snap off once the tool slides all the way around.

2. Remove the 4 screws around each corner of the Garmin.

3. Carefully open the device. Use your prytool to help separate the Garmin in one corner then use your fingers to carefully pull apart the Garmin. Disconnect the old battery and lift up the battery.

4. Now gently lift the screen of the Garmin using your prytool. Please note that the screen is connected by a ribbon cable. So do not separate or pull the screen too hard or too far away from the Garmin as you could destroy the cable. As you do gently lift the screen you will see the battery. You only need to lift the screen enough to see and remove the old battery.

5. Disconnect the old battery. Using the prytool here may be helpful lifting the old battery out. The old battery will be glued with a light adhesive so gentle strength may need to be applied.

6. Place your your new Garmin Nuvi 1200 Battery and connect it.

7. Close up the Garmin screen.

8. Gently snap the Garmin shut and replace the 4 screws you recently removed in step 2.

9. Snap back on the Garmin's faceplate.

10. Charge your new Garmin Nuvi 1200 Battery for 4 hours and then turn on.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

Magellan Roadmate 2000T Installation Instructions

The following Magellan Roadmate 2000T Battery Replacement Instruction guide can be used for the following models:

Magellan Roadmate 2000T Battery

1. To begin turn your Magellan Roadmate 2000T over and remove the 6 screws on the back of your magellan.

2. Carefully open or sepearte the 2 halves of the Magellan to see the battery. Please be careful to not pull the 2 halves to far apart as cable are attached to to both sides.

3. Disconnect the old battery and lift up the battery.

4. Replace the original Magellan Roadmate 2000T Battery with one from BatteryShip.com and connect the new battery.

5. Refasten the 6 screws you removed in step 1.

6. Charge your new Magellan Roadmate 2000T Battery for 4 hours.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.